Making a solar energy conversion breakthrough

This finding, which could lead to more power-efficient solar cells, was seeded in a near-half-century old discovery by Russian physicist Vladimir M. Fridkin, a visiting professor of physics at Drexel, who is also known as one of the innovators behind the photocopier.

The team, which includes scientists from Drexel University, the Shubnikov Institute of Crystallography of the Russian Academy of Sciences, the University of Pennsylvania and the U. S. Naval Research Laboratory recently published its findings in the journal Nature Photonics.

Their article "Power conversion efficiency exceeding the Shockley-Queisser limit in a ferroelectric insulator," explains how they were able to use a barium titanate crystal to convert sunlight into electric power much more efficiently than the Shockley-Queisser limit would dictate for a material that absorbs almost no light in the visible spectrum—only ultraviolet.

A phenomenon that is the foundation for the new findings was observed by Fridkin, who is one of the principal co-authors of the paper, some 47 years ago, when he discovered a physical mechanism for converting light into electrical power—one that differs from the method currently employed in solar cells.

The mechanism relies on collecting "hot" electrons, those that carry additional energy in a photovoltaic material when excited by sunlight, before they lose their energy. And though it has received relatively little attention until recently, the so-called "bulk photovoltaic effect," might now be the key to revolutionising our use of solar energy.

Solar energy conversion has been limited thus far due to solar cell design and electrochemical characteristics inherent to the materials used to make them.

"In a conventional solar cell—made with a semiconductor—absorption of sunlight occurs at an interface between two regions, one containing an excess of negative-charge carriers, called electrons, and the other containing an excess of positive-charge carriers, called holes," said Alessia Polemi, a research professor in Drexel's College of Engineering and one of the co-authors of the paper.

In order to generate electron-hole pairs at the interface, which is necessary to have an electric current, the sunlight's photons must excite the electrons to a level of energy that enables them to vacate the valence band and move into the conduction band—the difference in energy levels between these two bands is referred to as the "band gap."

This means that in photovoltaic materials, not all of the available solar spectrum can be converted into electrical power. And for sunlight photon energies that are higher than the band gap, the excited electrons will lose it excess energy as heat, rather than converting it to electric current. This process further reduces the amount of power can be extracted from a solar cell.

"The light-induced carriers generate a voltage, and their flow constitutes a current. Practical solar cells produce power, which is the product of current and voltage," Polemi said. "This voltage, and therefore the power that can be obtained, is also limited by the band gap."

But, as Fridkin discovered in 1969—and the team validates with this research—this limitation is not universal, which means solar cells can be improved.

When Fridkin and his colleagues at the Institute of Crystallography in Moscow observed an unusually high photovoltage while studying the ferroelectric antimony sulfide iodide—a material that did not have any junction separating the carriers—he posited that crystal symmetry could be the origin for its remarkable photovoltaic properties.

He later explained how this "bulk photovoltaic effect," which is very weak, involves the transport of photo-generated hot electrons in a particular direction without collisions, which cause cooling of the electrons.

This is significant because the limit on solar power conversion from the Shockley-Queisser theory is based on the assumption that all of this excess energy is lost—wasted as heat. But the team's discovery shows that not all of the excess energy of hot electrons is lost, and that the energy can, in fact, be extracted as power before thermalising.

"The main result—exceeding [the energy gap-specific] Shockley-Queisser [power efficiency limit] using a small fraction of the solar spectrum—is caused by two mechanisms," Fridkin said. "The first is the bulk photovoltaic effect involving hot carriers and second is the strong screening field, which leads to impact ionisation and multiplication of these carriers, increasing the quantum yield."

Impact ionisation, which leads to carrier multiplication, can be likened to an array of dominoes in which each domino represents a bound electron.

When a photon interacts with an electron, it excites the electron, which, when subject to the strong field, accelerates and 'ionises' or liberates other bound electrons in its path, each of which, in turn, also accelerates and triggers the release of others. This process continues successively—like setting off multiple domino cascades with a single tipped tile—amounting to a much greater current.

This second mechanism, the screening field, is an electric field is present in all ferroelectric materials. But with the nanoscale electrode used to collect the current in a solar cell, the field is enhanced, and this has the beneficial effect of promoting impact ionisation and carrier multiplication.

Following the domino analogy, the field drives the cascade effect, ensuring that it continues from one domino to the next.

"This result is very promising for high efficiency solar cells based on application of ferroelectrics having an energy gap in the higher intensity region of the solar spectrum," Fridkin said.