This user's guide introduces the TPS563252EVM and TPS563257EVM. These two devices differ in their light load behavior. The TPS563252 operates in Eco-mode and the TPS563257 operates in FCCM mode. This user's guide contains information for the TPS563252 and TPS563257 as well as support documentation for the TPS563252EVM and TPS563257EVM evaluation modules

Applications such as Hot-swap where Power FET is operated in saturation region under high stress, FET safe operating area (SOA) is a major concern for system designers. Designers need to study the FET SOA curve available in the manufacturers data sheet and determine if the FET can handle the power stress without undergoing damage. This application report covers the significance of FET SOA, how the manufacturers derive SOA plot, and how the hot-sw...

The TLV709 low-dropout (LDO) linear voltage regulator is a low quiescent current device that offers the benefits of a wide input voltage range and low-power operation in miniaturized packaging. The TLV709 is optimized to power microcontrollers and other low power loads for battery-powered applications.

The BQ79631 Evaluation Module user's guide describes the safety considerations, general features, theory of operation, hardware setup, and use of the BQ79631 EVM. Throughout this user's guide, the abbreviations BMS039, EVM, and the term evaluation module are synonymous with the BQ79631EVM unless otherwise noted. This EVM is an evaluation board for the BQ79631-Q1 to provide monitoring, protecting, and communications in high voltage environments wi...

The CC3120/CC3130/CC3135 and CC3220/CC3230/CC3235x devices are part of the SimpleLink microcontroller (MCU) platform, which consists of Wi-Fi®, Bluetooth® low energy, Sub-1 GHz and host MCUs. All share a common, easy-to-use development environment with a single core software development kit (SDK) and rich tool set.

The TI Dynamic Multi-Protocol solution allows multiple wireless protocols to run concurrently using a single radio, handling any timing conflicts that occur when multiple protocols request access to the radio during the same time period. To understand the system performance ramifications of operating multiple protocols in parallel, it is important to understand how the scheduler is making decisions.

The TPS6287x-Q1 is a family of pin-to-pin 6-A, 9- A, 12-A, and 15-A synchronous step-down DC/DC converters with differential remote sensing. For each current rating, there are full-featured device variants with I2C interface and limited-featured device variants without I2C interface. All devices offer high efficiency and ease of use. Low-resistance power switches allow up to 15-A continuous output current at high ambient temperatures.

Selecting the right wireless connectivity technology is a critical design decision from the beginning. This determines the protocol interoperability, distance, robustness and the use-cases for your application. This selection guide will walk you through several key decision requirements starting with the table below as a high-level summary of various wireless connectivity technologies.

The modern vehicle relies on high-speed automotive communication technologies that move data faster and farther to accelerate vehicle safety and autonomy.

With the increasing demand for animation in automotive lighting, LEDs must be controlled independently. Therefore, LED drivers with digital interfaces are essential to effectively drive pixel-controlled lighting applications. In exterior lighting, multiple lamp functions are typically located on different PCB boards with off-board wires connected to each other. It is difficult for a traditional single-ended interface to meet the strict EMC requir...

With the increasing demand for animation in automotive lighting, LEDs must be controlled independently. Therefore, LED drivers with digital interfaces are essential to effectively drive pixel-controlled lighting applications. In exterior lighting, multiple lamp functions are typically located on different PCB boards with off-board wires connected to each other. It is difficult for a traditional single-ended interface to meet the strict EMC requir...

The MSP-EXP430FR2355 LaunchPad™ Development Kit is an easy-to-use evaluation module (EVM) based on the MSP430FR2355 Value Line microcontroller (MCU). It contains everything needed to start developing on the ultra-low-power MSP430FR2x Value Line MCU platform, including on-board debug probe for programming, debugging and energy measurements. The board includes 2 buttons and 2 LEDs for creating a simple user interface. It also has an ambient l...

The TPS62903-Q1 is a highly efficient, small, and flexible synchronous step-down DC/DC converter that is easy to use. A selectable switching frequency of 2.5 MHz or 1.0 MHz allows the use of small inductors and provides fast transient response. The device supports high V OUT accuracy of ± 1.5% across the entire operating temperature range and enhanced load transient performance with the DCS-Control topology. The wide 3-V to 18-V input volt...

The MSPM0 SDK provides the ultimate collection of software, tools and documentation to accelerate the development of applications for the MSPM0 MCU platform. The software is designed for optimal performance and memory utilization, providing a consistent and cohesive experience with a wide variety of drivers, libraries and easy-to-use examples under a single software package

The LP-MSPM0L1306 LaunchPad™ development kit is an easy-to-use evaluation module (EVM) based on the MSPM0L1306. It contains everything needed to start developing on the MSPM0L1306 M0+ MCU platform, including on-board debug probe for programming, debugging and energy measurements. The board includes three buttons, two LEDs (one is an RGB LED), an analog temperature sensor, and light sensor.

Presently, there are two main types of selfie stick products on the market: single-axis selfie sticks and threeaxis selfie sticks. How can a selfie stick guarantee the shooting stability of mobile phone? Hand shaking of photographers can cause one-axis or three-axis jitter, in which the position and direction is detected by the selfie stick's built-in gyroscope sensor.

Failure to manage inrush current can lead to damaged cables, connectors, or fuses (11 Ways to Protect Your Power Path). High-voltage systems (100V+) often use precharged circuits to limit inrush current.

This manual describes the modules and peripherals of the MSP430FR4xx and MSP430FR2xx family of devices. Each description presents the module or peripheral in a general sense. Not all features and functions of all modules or peripherals may be present on all devices. In addition, modules or peripherals may differ in their exact implementation between device families, or may not be fully implemented on an individual device or device family.

Going wireless with the next generation of battery management systems (BMS) removes heavy communications cabling from inside EVs to help improve driving range and reliability. "When we create new solutions for wireless battery management systems for electric vehicles (EVs), our customers can design EVs that are lighter, go farther on a single charge and meet the highest level of functional safety standards to improve reliability."   &n...